Evaluation of Some Selective Surfaces Used for Solar Thermal Conversion Using the Calorimetric Method

Ali S Lahwal

doi:10.26629/uzjns.2026.04

PDF

Published: Apr 14, 2026

DOI: https://doi.org/10.26629/uzjns.2026.04

Keywords:

Selective surface, Absorptivity, Emissivity, Calorimeter, Black body, Solar energy, Solar collectors, Thermal conversion

Ali S Lahwal

Department of General, Faculty of Natural Resources, University of Zawia, Zawia, Libya.

https://orcid.org/0009-0008-7669-5415

Abstract

Knowledge of the selective radiative properties of surfaces is essential for the proper design of solar thermal collectors. Experimental results must directly reflect the conditions under which a surface will operate in order to accurately evaluate selective coatings for potential use in solar collectors. To achieve this, an instrument based on calorimetric techniques has been developed. It measures the solar absorptivity (\alpha) and infrared (IR) emissivity (\epsilon) of surfaces. These measurements determine the spectral selectivity of surfaces and assess their suitability for solar energy applications. The absorptivity (\alpha) and total hemispherical emissivity (\epsilon) are calculated as functions of temperature is measured by observing the rate at which a thermally isolated sample in an evacuated chamber heats up under real or simulated solar radiation. Emissivity is determined by measuring the rate at which the sample cools when shaded. These parameters allow comparison of the relative efficiencies of different surfaces over a range of operating temperatures. A graphite sheet was used as a blackbody reference to calibrate the instrument, and it was found that its absorptivity and emissivity are nearly equal, with values of approximately 0.94. Two additional samples were tested: a copper selective surface coated with aluminum and painted black, and an aluminum surface with V-grooving coated with a selective black paint. The results indicate that the copper-based surface is more suitable for solar collector applications than the aluminum surface, owing to the significant difference between its absorptivity and emissivity (\alpha=0.95,\epsilon= 0.25), which leads to higher thermal efficiency

How to Cite

[1]

A. S. Lahwal, “Evaluation of Some Selective Surfaces Used for Solar Thermal Conversion Using the Calorimetric Method”, UZJNS, vol. 3, no. 1, pp. 29–41, Apr. 2026.

Issue

Vol. 3 No. 1 (2026): Univ Zawia J Nat Sci

Section

Physics

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

You are free to:

Share — copy and redistribute the material in any medium or format.
Adapt — remix, transform, and build upon the material.

Under the following terms:

Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
NonCommercial — You may not use the material for commercial purposes.
No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.

References

[1] F. S. Johnson, “THE SOLAR CONSTANT,” Journal of the Atmospheric Sciences, vol. 11, no. 6, pp. 431–439, Dec. 1954, doi: https://doi.org/10.1175/1520-0469(1954)011%3C0431:TSC%3E2.0.CO;2.

[2] M. P. Thekaekara and A. J. Drummond, “Standard Values for the Solar Constant and its Spectral Components,” Nature Physical Science, vol. 229, no. 1, pp. 6–9, Jan. 1971, doi: https://doi.org/10.1038/physci229006a0.

[3] J. A. Duffie, W. A. Beckman, and J. McGowan, “Solar Engineering of Thermal Processes,” American Journal of Physics, vol. 53, no. 4, pp. 382–382, Apr. 1985, doi: https://doi.org/10.1119/1.14178.

[4] M. J. Kadhim, K. A. Sukkar, and A. S. Abbas, “Electrodepositing of Multi-Layer Ni-Ag Coated by Copper Nanoparticles for Solar Absorber,” Al-Khwarizmi Engineering Journal, vol. 15, no. 3, pp. 70–83, Sep. 2019, doi: https://doi.org/10.22153/kej.2019.06.009.

[5] T. S. Laszlo, “Solar Furnace in High-Temperature Research,” Science, vol. 124, no. 3226, pp. 797–800, Oct. 1956, doi: https://doi.org/10.1126/science.124.3226.797.

[6] AbeBooks, “Proceeding of the 1957 Solar Furnace Symposium. The Journal of Solar Energy Science and Energeering. Vol. 1, n. 2-3 by Simon e altri: (1957) | Studio Bibliografico Orfeo (ALAI - ILAB),” Abebooks.com, 2026. https://www.abebooks.com/Proceeding-1957-Solar-Furnace-Symposium-Journal/19806574997/bd (accessed Jan. 11, 2026).

[7] H. Messel and S. T. Butler: Solar Energy, Sydney, Pergamon Press, 1974.

[8] H. C. Hottel and B. B. Woertz, “The Performance of Flat-Plate Solar-Heat Collectors,” Journal of Fluids Engineering, vol. 64, no. 2, pp. 91–103, Feb. 1942, doi: https://doi.org/10.1115/1.4018980.

[9] J. T. Gier, and R. V. Dunkle, Transactions of the Conference on the Use of Solar Energy , 2, Part I, 41, U. of Arizona Press, 1958. “Selective Spectral Characteristics as an Important Factor in the Efficiency of Solar Collectors.”

[10] Tabor, H., Bull. Res. Coun. Israel, 5A, No. 2, 119 (January 1956). “Selective Radiation”.

[11] H. Tabor, “Solar Collectors, Selective Surfaces, and Heat Engines,” Proceedings of the National Academy of Sciences of the United States of America, vol. 47, no. 8, pp. 1271–1278, 1961, doi: https://doi.org/10.2307/71020.

[12] Martin, D. C. and Bell, R., Proceedings of the Conference on Coatings for the Aerospace Environment, WADD-TR-60-TB, Wright Air Development Division, Dayton, Ohio (November 1960). “The Use of Optical Interference to Obtain Selective Energy Absorption”.

[13] Edwards, D. K., Nelson, K. E., Roddick, R. D., and Gier, J. T., Report No. 60-93, Dept. of Engineering, univ. of California (October 1960). “Basic Studies on the Use and Control of Solar Energy”.

[14] Schmidt, R. N., Park, K. C., and Janssen, E., Tech. Doc. Report No. ML-TDR-64-250 from Honeywell Research Center to Air Force Materials Laboratory (September 1964). “High Temperature Solar Absorber Coatings, Part II”.

[15] M. Okuyama, K. Furusawa, and Y. Hamakawa, “Ni cermet selective absorbers for solar photothermal conversion,” Solar Energy, vol. 22, no. 6, pp. 479–482, 1979, doi: https://doi.org/10.1016/0038-092x(79)90019-7.

[16] V. G. Bhide, J.S. Vaishya, V. K. Nagar, and S. K. Sharma, “Choice of selective coating for flat plate collectors,” Solar energy, vol. 29, no. 6, pp. 463–465, Jan. 1982, doi: https://doi.org/10.1016/0038-092x(82)90054-8.

[17] J. H. Schön, G. Binder, and E. Bucher, “Performance and stability of some new high-temperature selective absorber systems based on metal/dielectric multilayers,” Solar Energy Materials and Solar Cells, vol. 33, no. 4, pp. 403–416, Aug. 1994, doi: https://doi.org/10.1016/0927-0248(94)90001-9.

[18] H. C. Hottel and T. A. Unger, “2 The properties of a copper oxide aluminum selective black surface absorber of solar energy,” Solar Energy, vol. 3, no. 3, pp. 10–15, Oct. 1959, doi: https://doi.org/10.1016/0038-092x(59)90134-3.

[19] P. Kokoropoulos, E. Salam, and F. Daniels, “Selective radiation coatings. Preparation and high temperature stability,” Solar Energy, vol. 3, no. 4, pp. 19–23, Dec. 1959, doi: https://doi.org/10.1016/0038-092x(59)90003-9.

[20] D. A. Williams, T. A. Lappin, and J. A. Duffie, “Selective Radiation Properties of Particulate Coatings,” Journal of Engineering for Power, vol. 85, no. 3, pp. 213–220, Jul. 1963, doi: https://doi.org/10.1115/1.3675262.

[21] H. S. Al-Jumaili, A. A. J. Al-Douri, and I. N. Al-Naimi, “Optical selectivity of manganese oxide film,”Renewable Energy, vol. 1, no. 2, pp. 219–222, Jan. 1991, doi: https://doi.org/10.1016/0960-1481(91)90078-4.

[22] Y. Shi and X. Yang, “Selective absorbing surface for evacuated solar collector tubes,” Renewable Energy, vol. 16, no. 1–4, pp. 632–634, Jan. 1999, doi: https://doi.org/10.1016/s0960-1481(98)00240-7.

[23] Z. Yin, Z. Xue, J. Zhang, and C. Shen, “Graded Al-N/Al absorbing surfaces for all-glass evacuated tubular collectors — R, D and production: Bridging the gap,” Renewable Energy, vol. 16, no. 1–4, pp. 624–627, Jan. 1999, doi: https://doi.org/10.1016/s0960-1481(98)00238-9.

[24] K. G. T. Hollands, “Directional selectivity, emittance, and absorptance properties of vee corrugated specular surfaces,” Solar Energy, vol. 7, no. 3, pp. 108–116, Jul. 1963, doi: https://doi.org/10.1016/0038-092x(63)90036-7.

[25] R. V. Dunkle, D. K. Edwards, J. T. Gier, and J. T. Bevans, “Solar reflectance integrating sphere,” Solar Energy, vol. 4, no. 2, pp. 27–39, Apr. 1960, doi: https://doi.org/10.1016/0038-092x(60)90112-2.

[26] E. Schmidt and E. Eckert, “Über die Richtungsverteilung der Wärmestrahlung von Oberflächen,” Forschung auf dem Gebiete des Ingenieurwesens, vol. 6, no. 4, pp. 175–183, Jul. 1935, doi: https://doi.org/10.1007/bf02578830.

[27] J. T. Gier, R. V. Dunkle, and J. T. Bevans, “Measurement of Absolute Spectral Reflectivity from 10 to 15 Microns,” Journal of the Optical Society of America, vol. 44, no. 7, pp. 558–558, Jul. 1954, doi: https://doi.org/10.1364/josa.44.000558.

[28] H. Willrath and R. B. Gammon, “The measurement of optical properties of selective surfaces using a solar calorimeter,” Solar Energy, vol. 21, no. 3, pp. 193–199, 1978, doi: https://doi.org/10.1016/0038-092x(78)90021-x.

[29] V. T. Sinha, “Heat transfer, J. P. Holman, McGraw-Hill, New York(1972). 462 pages.” AIChE Journal, vol. 18, no. 6, pp. 1280–1280, Nov. 1972, doi: https://doi.org/10.1002/aic.690180643.

[30] https://gyansanchay.csjmu.ac.in/wp-content/uploads/2022/01/CHE-S204-Chapter-8-Radiation_G5.pdf.A. K. Oppenheim, “Radiation Analysis by the Network Method,” Transactions of the American Society of Mechanical Engineers, vol. 78, no. 4, pp. 725–735, May 1956, doi: https://doi.org/10.1115/1.4013795.

[31] E. M. Sparrow, R. D. Cess, and E. Schmidt, “Radiation Heat Transfer,” Journal of Applied Mechanics, vol. 34, no. 4, pp. 1055–1055, Dec. 1967, doi: https://doi.org/10.1115/1.3607834